After you open your eyes on a lazy morning, do you wonder how you can get everything in reach?
Installing a floating nightstand is a good way to keep important things in place with your rader. In a bedroom, a floating nightstand not only holds things but also adds to the beauty of the room’s furniture.
Table of Contents
How to hang a floating nightstand?
They are usually put up on the wall by drilling through the back panel of their table tops. Most of the time, d-hooks are used to hang them. Another option is to use the french cleat system, which makes sure that the pocket holes are level without drilling through the nightstand.
If you want to put things on top of your bed for your own comfort, you need a floating nightstand like this one.
As someone who is thinking about how to hang a floating nightstand, we have a lot of ideas that will work for your floating nightstand.
Three great ways to hang or mount a floating nightstand:
To hang the nightstand, insert a cleat into a stud:
Make sure you find the wall studs and mark where you want to hang your nightstand. Drill a small hole into the stud before you put the screw in.
Finally, place the nightstand on the cleat. There is a screw on the bottom side that will go into the same stud to add extra support. You can use a trim head to drive through both pieces of the cleat when you’re done and finish it off with some putty that goes with the color of the cleat.
Mounting should be strong enough to hold the weight of the night stand.
Using an epoxy to hang your nightstand
Before you start, put the nightstand on. A stool that fits your bed’s height. Make sure you put it against the wall at the same level as your bed.
Make sure the nightstand is steady before you start applying epoxy. Continue to do this for the next 10 to 30 seconds, then stop and do something else. Through the braces, screw two screws into the nightstand and you’re done!
Attaching the floating nightstand to a wall with screws
Before you do anything else, you need to take the drawers off. Then, start drilling a lot of holes in the back of the floating nightstand. Make sure that you are drilling into the wall bracket, not the wall itself. Instead, don’t use the wall.
Screw your floating nightstand into place after you’ve done this. Make sure to put the drawers or storage back in. And your floating nightstand is done and ready to be used now, too.
How to make a floating nightstand?
Nightstands have become a must-have piece of bedroom furniture because they help you find things even if they’re a little difficult to find. People now buy floating night stands instead of night stands that have four legs.
With no extra work, you can make a DIY floating nightstand in your home and put it where you want it.
The tools you need:
- Polyurethane
- 1 Kreg screw
- Paint or stain
- Grit sandpaper
Six simple steps for making a DIY floating nightstand:
Making studs and chopping wood:
Chop your wood to the dimensions you want. For example, 1″ in height, 10″ in length, and 18″ in breadth. You can use studs to mark your 17″ board where they will hit the stud. If your board lacks studs, two or three pocket holes will suffice.
Remember to always pre-drill:
Always use a drill machine that is smaller than the screws you’re working with. It’s a good idea to use it to drill the bottom four corners of your floating nightstand.
Later, you can fill over the holes with a larger drill machine, but make sure the depth does not exceed 0.125 to 0.250 inches. The larger hole will always be on the same side of the pocket holes as the smaller holes.
Sandpaper with different grits:
You might want a smooth surface so that your children, if you have any, are not injured. In the beginning, a high grit sandpaper is recommended because it ensures a flawless and smooth surface.
Staining the nightstands, then:
You can start painting your nightstands as you collect and put together the parts. However, you can fill in the pocket holes with wood putty stain after you have all the wood pieces together.
Inserting an outlet (optional)
To determine the size of the hole, take measurements of your outlet designs and cut them to the appropriate size. You can measure it on cardboard as a guide or on the upper side of your nightstand—either way will work.
It will be much easier for you to visualize the position of your nightstand in the future if you plan it on paper or cardboard.
Hang floating nightstands
Choose a spot directly beside your bed to hang your nightstands. The most common rule is that nightstands should be hung 2-6 inches higher than the floor.
If you were unable to adhere to this rule, there is no need to be concerned because you can apply it to your height recommendations.
Your DIY floating nightstand will be finished once you complete the six steps outlined above. However, you will be working with delicate tools that, if not stored properly, can cause injury. Always keep the tools out of your children’s reach.
What are the measurements of a standard floating nightstand?
A floating nightstand is typically 24 to 28 inches tall and 11 to 15 inches wide. They are designed and built in such a way that they correspond to the standard height of a bed of 25 inches.
However, always place your nightstand at least 2 inches above the floor or mattress to make it easier to reach the top.
How do you make a floating nightstand headboard?
From a single sheet of plywood, you can easily construct a headboard with a floating nightstand. Begin by ripping a piece of plywood for the cubbies, one for the struts, and two for the cleats.
The next step is to milter one edge of the cleats into a 45-degree angle before arranging the struts and cleats on the headboard. Then glue the joints together.
After you’ve cut the cubbies and secured the cubby cart, simply attach the cubbies to the headboard and you’re done.
How do you make a floating nightstand with a light?
If you want a fancy DIY floating nightstand with light, all you need to do is install a power supply that will assist the light source in lighting the room. Get a switch and connect it to your power supply’s main DC connection, and you’re done.
How do you build a floating nightstand with a drawer and a shelf?
It’s very simple to build a floating nightstand with a drawer and shelf out of wood scraps.
By chopping the wood pieces at 45 degrees, the drawer dividers will be attached to the bottom of the nightstand. Attach the shelves in the same way that you did the drawers.
How to Build a Floating Nightstand with a USB Charging Station?
If you’re thinking about making a nightstand charging station, start by gathering a USB or charging station supply. Attach the power strip to the nightstand after drilling holes for the cord.
Your desired nightstand will be ready as soon as you plug your devices into your charging station.
As technology and science advance with a new surprise every other day, daily luxuries such as a hanging nightstand become a necessity. We frequently keep things in a specific location, but we have a tendency to forget things when they are needed.
Things on a nightstand will always be within reach in that situation.